Did I just Brick it??!?

In my quest to get an LED blinking using the Sparkfun GPIO Block (link here), I ran some example code (link here) in eclipse.

And let's just say I didn't use a resistor with my LED...hey it's just one LED right?

Well the blinking didn't occur the way I was expecting... but then again the pin numbering is a bit confusing.

I'll Paste the full pin numbering at the end of this post.

Long story short (no pun intended), I can no longer ping the Edison at the assigned static IP address.

What am I to do? Well I eventually went to the Serial Fall back, which was the first way I was able to ssh into the Edison.

How I did that:
1) With a micro-usb cable connected to the "console" port on the Sparkfun GPIO Block connected to my computer.
2) Went into Device Manager on my PC, then expanded "Ports" and read the COM# of the "USB Serial Port"... you'll know its the correct one for the Edison becasue it wont be present when the Edison isn't plugged in. Screen shot:

3) Fire up the application putty... if you don't already have it you can download it here

4) Select the "Serial" option, type COM# where # is the number you read from Device Manager->Ports
5) Change the Baud rate to 115200 from the default of 9600. Screen shot:

6) When that's all set, click "Open". You should be greeted with a login screen:

----------------------------------------------------------------------------------------------

Ok so I didn't brick it... That's a good thing.Why can't I see it on the network anymore??
It seems the IP address changed from what I had set as static previously, and its in an IP scheme that wont work on my LAN.

But why did the IP address change? According to the "/etc/wpa_supplicant/wpa_cli-actions.sh" file, the reason it's got this new funky IP is:

if [ "$CMD" = "P2P-GROUP-STARTED" ]; then
    GIFNAME=$3
    if [ "$4" = "GO" ]; then
        kill_daemon udhcpc /var/run/udhcpc-$GIFNAME.pid
        ifconfig $GIFNAME 192.168.42.1 up
        cp /etc/wpa_supplicant/udhcpd-p2p.conf /etc/wpa_supplicant/udhcpd-p2p-i$
        sed -i "s/INTERFACE/$GIFNAME/" /etc/wpa_supplicant/udhcpd-p2p-itf.conf
        udhcpd /etc/wpa_supplicant/udhcpd-p2p-itf.conf
    fi



... So unless I fried it and made it do something strange... It seems I've switched the WiFi mode to P2P??
I need to do more investigating ... I'll update when I get that LED Blinking :D

Also the pic reference I mentioned earlier in this post:

Edison Pin (Linux)	Arduino Breakout	Mini Breakout	MRAA Number	Pinmode0	Pinmode1	Pinmode2
GP12	3	J18-7	20	GPIO-12	PWM0
GP13	5	J18-1	14	GPIO-13	PWM1
GP14	A4	J19-9	36	GPIO-14
GP15		J20-7	48	GPIO-15
GP19		J18-6	19	GPIO-19	I2C-1-SCL
GP20		J17-8	7	GPIO-20	I2C-1-SDA
GP27		J17-7	6	GPIO-27	I2C-6-SCL
GP28		J17-9	8	GPIO-28	I2C-6-SDA
GP40	13	J19-10	37	GPIO-40	SSP2_CLK
GP41	10	J20-10	51	GPIO-41	SSP2_FS
GP42	12	J20-9	50	GPIO-42	SSP2_RXD
GP43	11	J19-11	38	GPIO-43	SSP2_TXD
GP44	A0	J19-4	31	GPIO-44
GP45	A1	J20-4	45	GPIO-45
GP46	A2	J19-5	32	GPIO-46
GP47	A3	J20-5	46	GPIO-47
GP48	7	J19-6	33	GPIO-48
GP49	8	J20-6	47	GPIO-49
GP77		J19-12	39	GPIO-77	SD
GP78		J20-11	52	GPIO-78	SD
GP79		J20-12	53	GPIO-79	SD
GP80		J20-13	54	GPIO-80	SD
GP81		J20-14	55	GPIO-81	SD
GP82		J19-13	40	GPIO-82	SD
GP83		J19-14	41	GPIO-83	SD
GP84		J20-8	49	GPIO-84	SD
GP109		J17-11	10	GPIO-109	SPI-5-SCK
GP110		J18-10	23	GPIO-110	SPI-5-CS0
GP111		J17-10	9	GPIO-111	SPI-5-CS1
GP114		J18-11	24	GPIO-114	SPI-5-MISO
GP115		J17-12	11	GPIO-115	SPI-5-MOSI
GP128	2	J17-14	13	GPIO-128	UART-1-CTS
GP129	4	J18-12	25	GPIO-129	UART-1-RTS
GP130	0	J18-13	26	GPIO-130	UART-1-RX
GP131	1	J19-8	35	GPIO-131	UART-1-TX
GP134		J20-3	44
GP135		J17-5	4	GPIO-135	UART
GP165	A5	J18-2	15	GPIO-165
GP182	6	J17-1	0	GPIO-182	PWM2
GP183	9	J18-8	21	GPIO-183	PWM3